News of General Discussions about iGO core - Page 158

HOW TO INSTALL iGO PRIMO ON A VIAMICHELIN X960 NEW EDITION

SHOULD ALSO WORK FOR X970, X980 & OTHER VIAMICHELINS

WARNING ~ I know everything about nothing, & nothing about everything.
On & off over the last year I have been thinking about updating my x960, but as it is not the most common sat nav on the market I ...

ok where do i put the following files please

.ftr
.hsp
.fda

also my speed cam files are in .txt is that correct or do i need to convert them?

Hi
has enyone had the problem of the first words in directions not being spoken or only the last part of the word?
I've just installed Primo on my Chines in car unit and everything is working fine except the speech issue. I had IGO8 on the SD before and had no problems with it.

Thanks

A list of which skins work with the different versions and releases of the various iGO products would be very helpful.

Also helpful would be notes if a skin that works has issues with certain resolutions or specific devices.

For example, GJ6.14_beta_03.zip works fine on iGO 8.3.2.96054 at 320x240 but at 480x272 causes an FFUI error during start, which can be dismissed then it functions perfectly fine - at least on a Nextar 43LT (Q4 ...

Hi,
Could u help for me please.
I have Mio DigiWalker C320 V.3.3 May 3 2007 and I would use with new /fbl/ map but I can't. I Changed the map but is unlocked. I used this one {dead link} but it not worked. Is there any idea. Because Mio is enought for me but the miomap unusless, to old.

Many thank for your help.

I finally got a version of Primo and a skin that work together. iGO 8.5.11.168090 with GJA_v2.25.

When I run the demos and when I program a route, the TTS voices have pauses when they say street names.

It does that with or without the skin active.

It's on a Nextar 43LT, using the 2010 Q2 Tele Atlas maps and POIS, no 3D buildings or DEM files.

So far, I've not had good results on ...

i went to http://www.lightinthebox.com where they told me i could purchase an sd card with igo on it. i have an XO VISION 1840BT Navi with gps loaded on an sdcard they told me that it would work but id dont wanna mess up my system hoping maybe to findout more info on igo or maybe download from online any info will be good!!!!

what they sell is : 2GB SD Card with GPS Map ...

Thank you, Nabi for bringing version 1.2 to the forum.

A small question:

I've download it and tried running it on my C-310. The application
invokes but unable to run (The blue bar at the bottom almost reaches the right side of the screen, but gets stuck).

It won't run and after deleting SAVE folder it keeps complaining
about not enough memory. This has not changed even after I
commented all the lines regarding TTS ...

When I reach the destination I get the FFUIERROR: unknown object identifier
Identifier=
Script "d Start AutoExitShutdown"
Command 3

I am using a car cursor in Mio C310X with Gurjon 6.18 and iGO8.

Another site had some instructions as follows for this:

That code is designed to hide the cursor car selection buttons in the diMka skins...

Open 3DCars/ui/3DCars.ui and remove the following lines...
sld_AVS12.hide
txt_AVS12.hide
btn_AVS12.hide
Save the file and you won't get ...

Every time I launch it, it goes through the setup wizard. I have it on a 4gig SD along with the latest Mobipocket.

Without hacking into the internal software, this one is fixed to launch \SDMMC\iGO.exe with the navigation button. (Which is how I got Mobipocket on, put the script and two exe's in the iGO folder, renamed appropriately then launched "navigation".)