I have found a new meta code so enjoy
USA_Canada 900_4608

; USA_and_Canada v900.4608
60 B9 19 F1 88 55 07 E7 D8 72 B9 C2 1A 5E 0B C3 USA_and_Canada-670.meta

Hi there,
I have iGo Primo 2.4 installed on my Eonon D5151, an in -dash nav unit.

Im trying to figure out how to turn off the Destination Menu, the menu that gives you the option to turn off when you reach your destination and whatnot, and it's supposed to be in the Extra Settings menu.

I have the UI Labs enabled and can access it fine, but i can't seem to find the extra ...

hiya all

just got a second hand chinese noname system as its got 128mbram, runs igo no prob at all, installed i3-primo which runs with all the bobs n whistles but on startup it stops with message

NAVIEXTRAS Warning!!! The device connects to a server different from the NE live server!!!

is there a way of getting rid of this warning permanently so i dont have to tap ok button every time i start programme? ...

Hi Hope someone can help resolve a issue a work friend has with his Chinese sat nav running Igo Primo 2 / Sygic Fleet. Sygic runs fine and has no issues but not the preferred software as it doesn't seem to route as well as Igo. Igo with 3d buildings removed, all unneeded voices and so on removed still after various amounts of time gives the small Error out of memory message, requested:1265460 Cache: 2912396 ...

hi all,is there a way to increase screen res for net book use,ive been having a play around with wince emulators and igo8,loads up ok,navigates through menus ok.I've not sourced a gps antenna as yet so can't say it all runs smoothly,I would just like to get it to fill the screen a little more.Res of the screen is 1024x600,at the moment it's using 800x480.Also can truck settings be added to igo8 as this is ...

Hello there
I have a device with iGO Primo 2
How do I do on the side where it says the same road speed limit it also say my speed
for example i saw in IGO MY WAY its saw to road speed limit and my speed
Sorry for the english and thanks :)

Hi, I have a Mio c250, currently with MioPocket SD, which I have TomTom7 and Igo8, I would like to know if it is possible to run the Igo Primo on my PNA, as this only has 32 Megs of Ram. although I've seen this video http://www.youtube.com/watch?v=LHvips4nqAU in which they seem to have been able to make it work ... sorry for my English is not very good.

Sorry for being so dummy, I have't done any hacking of tomtoms and this seems challenging if not impossible
I'm moving to Australia from US and I wonder if it's possible to get an Ausralian map to work with this version.

device details are below.

thanks in advance



DeviceName=TomTom ROME
DeviceVersionHW=ROME
DeviceSerialNumber=woops
DeviceUniqueID=woops
RamDiskVersion=20040301
BootLoaderVersion=10012
LinuxVersion=1000
ApplicationVersionVersionNumber=8083
ApplicationVersion=9669
UserLanguage=English US

Any help would be appreciated

Hello everyone,

I'm new here and i have get some amcor 3750 satnav device to play with.
I love to "play" which old electronics.
unfortunately there was no sd card with maps with it.
I have not much information about the device because the company get busted.
I find this information online
''Thus, the 3750 is built around a 22-channel Centrality Atlas-II receiver, accompanied by a Centrality Atlas-II 300Mhz CPU and 64 MB Flash / ...

Does anyone have maps for tt7 ?
Pref Benelux but west europe is also good.
Can i install tt8 maps ?

Tnx in advance