[Discussion] Navcore 9.510 with automatic power on function

You can find the Navcore in the Navcore section.
Please leave your feedback and comments here.
All credits for the kernel mod go to Keesie74!

Thanks, Downunder35m and Keesie74,

Automatic Power On is oké.

With the skinchooser (default 40) this results with TT GO630:

A. No automatic switching to nightcolors.
B. I''ll be back sound when switching off.
C. no line out (cable) signal by music with TT Jukebox.

Changed with skinchooser to 25 and than A and C is now oké but no sound when shutting down.

With the DSAtool 9510 NC, A and C did work good but no sound when shut down power. (B)
:D

Automatic switching to night colors either works over the sensor (correct TT model and correct emulation needed) or by the time.
For the time switching I can't help, for the sensor it will only work on a X30 device in X30 mode - but that is old news ;)
I have the shutdown sound working in X40 too but have to agree that the later V9 Navcores cuse unnecessary trouble with the sounds.
So far there is no common solution as it depends on the device and emulation in use.
But that was the case with previous NC's too and is not caused by the kernel in use.

Did you check if by any chance the music would be transmitted over FM when Line Out is selected?
Asking as there was a similar "bug" in the old Navcores.

TT GO630 has no FM transmitter

True, my fault!
Was thinking of my device :(
The 630 was always a bit tricky and I'm acually surprised that this standard version works on it with no problems.

ixlion wrote:With the skinchooser (default 40) this results with TT GO630:
A. No automatic switching to nightcolors.

Downunder35m wrote:Automatic switching to night colors either works over the sensor (correct TT model and correct emulation needed) or by the time.

Automatic switching to night, by sensor or time, does not function in emu 40, but it does function by time in emu 50.

tendriver wrote:Automatic switching to night, by sensor or time, does not function in emu 40, but it does function by time in emu 50.

With the new NC in my TT GO630 automatic switching to night it's done by the sensor. ( in emu x30).
Disadvantage of emu 50: no jukebox.
So I prefer emu x30, because night sensor function ok and playing music via Line out audio cable also ok.

ixlion wrote:1. With the new NC in my TT GO630 automatic switching to night it's done by the sensor. ( in emu x30).
2. Disadvantage of emu 50: no jukebox.
3. So I prefer emu x30, because night sensor function ok and playing music via Line out audio cable also ok.

1. X20 is by sensor also.
2. BIG Advantage of emu 50, Voice Command & Control!!
3. We just advise. It is always the users decision.

I only get IQ routes to show with x40 not X50 tt720go ?
does x50 do IQ routes?
thanks

gatd wrote:I only get IQ routes to show with x40 not X50 tt720go ?
does x50 do IQ routes?
thanks

IQ Routes will show on any device that can run navcore 9.0XX or higher with current maps 910.4892, 4939, 4956, 4958. 1 exception: 910.4973 for Carminat only requires 8.2XX or higher. IQ Routes will also show using just about any emu.

Disclaimer: This "Power On" version is new & may still have a bug or 2 in it.

don't works the TTS voices on my TT 720T, but I like it!

That is not really a statement for an owner of a 720 ;)
Especially on the X20 and X30 series TTS works very good, so I can only suspect the problem to be with your way of installing the voices.
Or you use an unsuitable emulation.
Kate is included and should work just fine.

well I choose the X20 Emulator and Kate didn't work. Also Downloaded another TTS voice and didn't work either. If you help me to find why, will be very glad. I just wipped everything from the device (except the maps) and installed this mod. Thanks!

Go to the last page in the menu and use the skin chooser to switch to X50 emulation.
A double tap in the center of the screen will reboot with the selected emu.

Thank You for this navcore