iGo Primo 2. No Signal

do you have to do this everytime you change the baud rate, i downloaded the software thats on here called WinCE Device Information V2 but i dont know how to use it. it says that this can tell you all the information about your gps.

kraigh98 wrote:do you have to do this everytime you change the baud rate, i downloaded the software thats on here called WinCE Device Information V2 but i dont know how to use it. it says that this can tell you all the information about your gps.

Put all the files on your device and run WinCE Device Information.exe

Follow the instructions.

A text file will be created, Post it here...

My device is a car stereo.Ive tried to run it but it doesn't load it just doesn't do anything.

How are you trying to run it?

From the sd card slot. is that the correct way.
How do I get it to run.

I've tries from the USB slot aswell. Still doesn't allow me to do anything

You will need to temporarily replace primo 2 on the SD card to run it.

WinCE Device Information V2, 2011 Fatboyfun http://www.navitotal.com

DEVICE INFORMATION.
Screen resolution 800x480
Windows CE 6
Free / Total RAM available 95004 KB / 113508KB

AVAILABLE DRIVES GREATER THAN 128MB. (Free / Total)
NOTE: Mortscript only reads up to 2047MB
\StorageCard (2047MB/2047MB)

GPS INFORMATION.
Port=2
Baudrate=4800

Visit http://www.navitotal.com for all your GPS needs!

this is what i got when i run the software

This tells us the port and baud settings are correct.

Question, Which build of iGO are you using?
Try using Yurbuh Tuggly's build to confirm a device or software issue.

And it's possible that this device has something wrong with the GPS, or needs a different antenna.

How do i find out what build of iGo i am using,

what makes you think there could be something wrong with the antenna,

Ive had a look and found i am using Product Version 9.6.5.211211 file version 9.6.5.0

i just looked at the torrent and i think i am using Yurbuh Tuggly's version.

kraigh98 wrote:How do i find out what build of iGo i am using,

Go to settings, about and look there.

its ok i found it :-).

i was just looking through my save profile in primo and i came across the system file and it says this:

[gps]
baud="57600"
gpstime="1350410030"
last_gps_date="2012.10.16."
last_gps_time="18:25:06.000"
port="2"

why would the baud rate be different to that of the one i posted earlier

Do you know where you got it from?

There are builds of iGO (Assembled by someone, usually for a specific device) that give all sorts of problems on other devices, trying to fix every issue is sometimes impossible.

I suggest trying a known working build to compare with what's installed now, If it's the same then i suspect a hardware issue, could be anything from a later revision GPS receiver which needs a slightly different antenna to the original device, Or it was just faulty from the start.

EDIT: Deleting the save folder would have fixed it, change the baud rate in the system file...

if i delete the save folder will i delete all the favourites stored. .. i think i have the version by Yurbuh Tuggly's i got it from here as i went to download the torrent file and i recognised the torrent file already on my computer.

kraigh98 wrote:if i delete the save folder will i delete all the favourites stored. .. i think i have the version by Yurbuh Tuggly's i got it from here as i went to download the torrent file and i recognised the torrent file already on my computer.

Just either rename the save folder to something else or copy it first to your computer and then delete it from your device. This way you can rename it back or just copy it again from your computer.